Music / Speaker Cabinets
Ampeg SVT 210AV Speaker Cabinet Owner's Manual
Get the most out of your Ampeg SVT 210AV speaker cabinet with this owner's manual. Includes setup instructions, connection guidelines, technical specifications, and safety precautions.
Quick answers from the manual
Quick answer
- The Ampeg SVT 210AV is an 8-ohm, 200W RMS speaker cabinet. Connect it to your amplifier using a non-shielded speaker cable. Do not stack more than two cabinets high. p. 2, 3, 4
Key actions
- Connect amplifier to cabinet p. 3
- Daisy-chaining cabinets p. 3
Problems and fixes
Cable type issues
Never use (shielded) instrument cable to connect speakers to an amplifier.
p. 3Show 3 more answers Show less
Maintenance and reset
- Cleaning the cabinet p. 4
Technical specifications
| Parameter | Value | Meaning | Pages |
|---|---|---|---|
| Impedance | 8 ohms | Nominal impedance | p. 4 |
| Power Rating | 200 W RMS | Continuous power handling | p. 4 |
| Inputs | 2 x 1/4" parallel jacks | Connection type | p. 4 |
Where to find it in the PDF
- Front Cover p. 1
- Introduction and Safety p. 2
- Connections and Diagrams p. 3
- Specifications and Service p. 4
Table of contents
Manual images
Click an image to enlargeQuick guide from the manual
The Ampeg SVT 210AV is a high-performance speaker cabinet designed for use with bass amplifier heads, such as the Micro-VR. Key operational requirements include:
- Safety: Do not stack more than two cabinets high. Ensure the surface is sturdy and level.
- Cables: Always use a high-quality, non-shielded speaker cable. Never use a shielded instrument cable to connect the speaker to an amplifier.
- Connections: The cabinet features two 1/4" parallel jacks. You can use the output jack to daisy-chain a second cabinet.
Introduction
The SVT 210AV is designed to provide the classic look and sound of the SVT-Series in a compact format. It features two ten-inch Eminence speakers and is built to withstand the demands of professional use.
Connections
The rear panel contains two 1/4" TS jacks wired in parallel. This allows for flexible connectivity:
- Input: Connect the speaker-level output from your amplifier to the input jack.
- Output: Use the output jack to connect a second speaker cabinet in parallel.
Note: Connecting a second cabinet will present a total load of 4 ohms to the amplifier. Ensure your amplifier is capable of handling a 4-ohm load before connecting a second cabinet.
Technical Specifications
The SVT 210AV is rated for 200W RMS power handling at 8 ohms impedance. It is constructed from birch plywood and includes a stylish top handle for portability.
Maintenance
The cabinet is covered with a durable fabric-backed vinyl material. To clean, use a dry, lint-free cloth. Do not spray cleaning agents directly onto the cabinet, and avoid abrasive cleansers that may damage the finish.
Service Information
If you encounter issues, visit www.ampeg.com for support or call 1-800-898-3211 (7 am to 5 pm PST, Monday-Friday). For users outside the U.S., contact your local distributor.
Official resources from the manual
Practical help
Common problems
No sound or weak signal
Ensure you are using a non-shielded speaker cable. Shielded instrument cables are not suitable for connecting speakers to an amplifier.
Amplifier overheating or shutting down
Check if the total impedance load is too low. Connecting two 8-ohm cabinets in parallel creates a 4-ohm load; ensure your amplifier supports 4-ohm operation.
Before use
- Place the cabinet on a sturdy, level surface.
- Verify the amplifier output is compatible with an 8-ohm load.
- Use a high-quality, non-shielded speaker cable.
- If stacking, do not exceed two cabinets in height.
Show more Show less
Specs in practice
- Impedance: 8 ohms
- The electrical resistance of the cabinet. Your amplifier must be rated to handle this load.
- Power Handling: 200W RMS
- The continuous power the cabinet can safely handle from the amplifier.
- Parallel Jacks
- Allows you to connect a second cabinet to the same amplifier output.
Images and diagrams
- The System Block Diagram shows the two 10-inch speakers wired in parallel to the input/output jacks.
- The Rear Panel diagram identifies the Input and Output jacks for connecting your amplifier and daisy-chaining additional cabinets.
Model compatibility
- Designed as an ideal companion to the Micro-VR amplifier head.
- Compatible with any amplifier capable of driving an 8-ohm load (or 4-ohm if daisy-chaining two cabinets).
Manual page author
David Miller
Documentation analyst