User Manual for Neo Tools 190G Gas Lamp (20-021, 20-022)

Quick guide for the Neo Tools 190G gas lamp, covering setup, cartridge replacement, ignition, safety precautions, and maintenance for models 20-021 and 20-022.

Table of contents

Quick guide from the manual

This document provides essential instructions for the safe operation and maintenance of the Neo Tools 190G gas lamp (models 20-021 and 20-022). Always use the device outdoors or in well-ventilated areas, keep it away from flammable materials, and ensure the gas cartridge is replaced only when completely empty and in a safe environment.

Device Description

The lamp is a portable gas burner designed for use with 190g butane cartridges. Key components include:

Gas control knob
Nozzle
Gas cartridge cover
Handle

Installation

The device requires a 190g butane gas cartridge (not included). Follow these steps to install:

Ensure the lamp valve is fully closed by turning the knob in the '-' direction.
Check that the gasket is in place and in good condition.
Insert the gas cartridge into the housing.
Position the lamp vertically and tighten the fixing nut onto the housing by holding the top of the cartridge compartment.
The cartridge will be punctured during this process. Do not attempt to remove it once punctured.

Operation

To ignite and use the lamp:

Slightly open the valve by turning the knob towards '+'.
Immediately ignite the gas at the nozzle tip.
Adjust the flame size as needed. Wait about 1 minute before use, keeping the lamp in an upright position.
To extinguish, turn the valve fully in the '-' direction.
For best performance, keep the gas cylinder vertical or at an angle no greater than 45°.

Cartridge Replacement

Only replace the cartridge when it is completely empty. Perform this task outdoors, away from people and ignition sources. Ensure the valve is closed and the burner is cold before unscrewing the lower cap to remove the empty cartridge and insert a new one.

Maintenance and Safety

Cleaning: Use a damp cloth and soapy water. Never use abrasive agents.
Storage: Store in a cool, dry, well-ventilated place, upright and out of reach of children. Never store in a cellar or poorly ventilated enclosed space.
Troubleshooting: If the lamp fails to ignite, it may be due to moisture (dry the lamp) or a blocked nozzle. Do not attempt to repair the nozzle yourself; contact the manufacturer's service department.

Technical Specifications

Gas flow rate: 87 g/h
Power: 1.2 kW
Cartridge: Butane (190g)
Automatic piezo ignition: Available on model 20-022 only

Service Contact

For warranty and service inquiries, contact GTX Service Sp. z o.o. Sp.k., ul. Pograniczna 2/4, 02-285 Warszawa, Poland. Email: [email protected]. Website: gtxservice.com

Official resources from the manual

Official resource gtxservice.com

Practical help

Common problems

Difficulty igniting the lamp

The lamp may be damp; dry it thoroughly. If the issue persists, the nozzle may be blocked or dirty; do not repair it yourself, contact service.

Gas smell or leak

Immediately move the device outdoors to a well-ventilated area away from open flames. Check for leaks using soapy water, never an open flame.

Cartridge does not puncture or gas does not flow

If the cartridge was punctured but no gas flows, or if there are issues with the valve, contact the manufacturer's service department.

Before use

Check that the gasket is present and in good condition.
Ensure the valve is fully closed (turned to '-').
Verify the work area is well-ventilated and free of flammable materials.
Ensure the gas cartridge is 190g butane.
Check that the device is not leaking or damaged.

Specs in practice

Gas flow rate (87 g/h): The rate at which the device consumes fuel during operation.
Power (1.2 kW): The thermal output capacity of the burner.
Automatic piezo ignition: Feature present only on model 20-022 for easier lighting without external flame.

Model compatibility

Designed for use with 190g butane gas cartridges.
Not compatible with other gas types or cartridge sizes.
Model 20-021 does not have automatic piezo ignition; model 20-022 does.

Show more Show less

Manual page author

Emily Carter

User documentation editor

Prepares concise manual descriptions and highlights the most useful setup, operation, and maintenance information for readers.