Hvac / Air Conditioners
ACiQ 06W-HH-MB Air Conditioner Remote Controller User Guide
Quick guide for the ACiQ 06W-HH-MB remote controller, covering battery installation, basic operation modes, timer settings, and advanced functions like ECO/GEAR, Swing, and Follow Me.
Table of contents
Quick guide from the manual
This document provides instructions for operating the ACiQ wall-mounted air handler remote controller. Key models covered include ACiQ-06W-HH-MB, 09W-HH-MB, 12W-HH-MB, 18W-HH-MB, and 24W-HH-MB. Ensure the unit is plugged in and powered before operation.
Handling the Remote Controller
To insert or replace batteries, slide the back cover downward, insert two R03/LR03 3.0V dry batteries matching the (+) and (-) symbols, and slide the cover back into place. Do not mix old and new batteries or different types. Remove batteries if the remote will not be used for more than 2 months.
Basic Operation
The remote must be used within 8 meters of the unit. The unit will beep when a signal is received. Use the MODE button to cycle through AUTO, COOL, DRY, HEAT, and FAN modes. Use the TEMP buttons to adjust temperature (16-30°C) and the FAN SPEED button to adjust airflow.
Setting the TIMER
The timer allows you to set the unit to turn on or off automatically. Press the TIMER button to initiate the sequence, then use the TEMP up/down buttons to set the desired time. The time increases in 30-minute increments up to 10 hours, and 1-hour increments thereafter. Point the remote at the unit and wait 1 second to activate.
Advanced Functions
- Swing: Press the SWING button for horizontal louver movement. Hold for 2 seconds to initiate vertical auto-swing.
- ECO/GEAR: Press to enter energy-efficient modes (ECO, GEAR 75%, GEAR 50%). Only available in COOL mode.
- Follow Me: Enables the remote to measure ambient temperature at its current location instead of the indoor unit.
- LED: Press to turn the indoor unit display on or off. Hold for 5 seconds to display the actual room temperature.
- Lock: Press CLEAN and TURBO simultaneously for 5 seconds to lock/unlock the remote buttons.
Specifications
- Rated Voltage: 3.0V (2x R03/LR03 batteries)
- Signal Range: 8 meters
- Operating Environment: -5°C to 60°C
Manufacturer information
ACiQ
Practical help
Common problems
Remote signal not received
Ensure you are within 8 meters of the unit and that there are no obstructions like curtains or direct sunlight interfering with the infrared receiver.
Insufficient cooling or heating
Check if Silence function is active (lowers compressor frequency) or if ECO/GEAR mode is limiting performance.
Buttons do not respond
Check if the LOCK function is enabled (indicated by a lock icon). Press CLEAN and TURBO simultaneously for 2 seconds to disable.
Before use
- Ensure the air conditioner is plugged in and power is available.
- Install two fresh R03/LR03 3.0V batteries.
- Verify the remote is within 8 meters of the indoor unit.
- Remove any obstructions between the remote and the unit's infrared receiver.
Specs in practice
- Signal Receiving Range
- The maximum distance (8m) from which the remote can effectively control the unit.
- Temperature Range
- The adjustable range is 16-30°C (60-86°F).
Images and diagrams
- The remote features a central OK button surrounded by navigation arrows and function buttons like MODE, SET, and TIMER.
- The LCD screen displays mode icons (AUTO, COOL, DRY, HEAT, FAN), fan speed levels, and active features like ECO, GEAR, or LOCK.
Model compatibility
- Some functions (e.g., Breeze Away, Fresh, Sleep) may not be available on all models.
- If the indoor unit does not support a specific function, pressing the corresponding button on the remote will have no effect.
- Cooling-only models do not support HEAT or AUTO modes.
Manual page author
Emily Carter
User documentation editor
Prepares concise manual descriptions and highlights the most useful setup, operation, and maintenance information for readers.