Assembly and User Guide for Holiday Living 24-Inch Playful Doodle LED Light ES69-400L

Quick guide for the Holiday Living 24-Inch Playful Doodle LED Light (ES69-400L). Includes assembly steps, safety warnings, troubleshooting, and maintenance instructions.

Quick answers from the manual

Quick answer

This manual provides assembly, maintenance, and safety instructions for the Holiday Living 24-Inch Playful Doodle LED Light (ES69-400L). p. 1, 2, 3

Key actions

Assemble the product using the provided hardware (AA, BB) and steps 1-6. p. 3
Replace the fuse by sliding open the plug cover and inserting a 3 Amp, 125 Volt fuse. p. 2

First start

Ensure all parts are present, assemble according to the steps, and connect to a GFCI outlet if used outdoors. p. 1, 3

Show 4 more answers Show less

Problems and fixes

No lights light up

Check power, extension cord, and fuse.

p. 1

Water inside bulb

Hold bulb to drain water.

p. 2

Maintenance and reset

Replace lamps by pulling the lamp and base out, and inserting a new 3V 0.06W LED lamp. p. 2

Technical specifications

Parameter	Value	Meaning	Pages
LED Lamp	3V 0.06W	Replacement lamp specification.	p. 2
Fuse	3 Amp, 125 Volt	Fuse rating.	p. 2

Where to find it in the PDF

Safety, Troubleshooting, and Preparation p. 1
Maintenance and Lamp Replacement p. 2
Assembly Instructions p. 3

Table of contents

Quick Guide

This manual provides instructions for the assembly, maintenance, and safe operation of the Holiday Living 24-Inch Playful Doodle LED Light (Model ES69-400L). The product is intended for seasonal use only and is not for permanent installation.

Assembly Instructions

Estimated assembly time is 5 minutes. Before beginning, ensure all parts are present and undamaged.

Assembly diagram for connecting sections.

Step 1: Attach (B1) and (C1) to (A1), secure with (AA).
Step 2: Attach (B2) and (C2) to (A2), secure with (AA).
Step 3: Combine (A1) and (A2), secure with (AA).
Step 4: Attach (D) on (A), secure with (AA) on the front. Attach (E) to the back of (A).
Step 5: Place (F) around the neck, secure with the pre-attached Velcro. Place (G) around the dog.
Step 6: Secure the item into the ground using (BB).

Maintenance

Replacing the Fuse

If the lights do not work, the fuse may be blown. To replace:

Unplug the product from the outlet.
Slide open the fuse access cover on top of the attachment plug.
Remove the old fuse carefully.
Replace with a 3 Amp, 125 Volt fuse.
Slide the fuse cover closed.

Replacing Lamps

The product uses 3V 0.06W LED lamps. To replace:

Unplug the product.
Pull the lamp and plastic base straight out of the lamp holder.
Replace with a new 3V 0.06W LED lamp (provided with the product).
If the base does not fit, remove the base of the burned-out lamp by straightening the leads, thread the new lamp leads through the holes in the old base, and bend the leads up to touch the contacts.

Troubleshooting

One section does not light: Check bulbs; replace any broken or loose bulbs.
No lights light up: Ensure power is on, check the extension cord, and check the fuse in the plug.
Water inside bulb: There are drains at the top and bottom of the bulb. Hold the bulb as shown in the diagram to release the water.

Safety Information

Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When used outdoors, connect to a Ground Fault Circuit Interrupting (GFCI) outlet.
Do not mount near gas or electric heaters, fireplaces, candles, or other heat sources.
Do not secure wiring with staples or nails.
Do not let lamps rest on the supply cord or any wire.
Unplug when leaving the house or unattended.
This is an electric product, not a toy. Keep away from small children.
Do not close doors or windows on the product or extension cords.
Do not cover the product with cloth, paper, or any material when in use.

Practical help

Common problems

One section does not light

Check each bulb one at a time; replace any broken or loose bulbs.

No lights light up

Ensure power is on, check the extension cord, and inspect the fuse in the plug.

Water inside the bulb

Hold the bulb according to the diagram to allow water to drain from the top and bottom drains.

Before use

Verify all parts are present against the package contents list.
Inspect for damaged, cut, or frayed wire insulation.
Check for cracks in lamp holders or enclosures.
Ensure no loose connections or exposed copper wire.
If using outdoors, ensure connection to a GFCI outlet.

Show more Show less

Images and diagrams

Assembly involves connecting sections A1, A2, B1, B2, C1, C2, D, E, F, G using hardware AA and BB.
Use the pre-attached Velcro to secure part F around the neck.

Model compatibility

Seasonal use product; not intended for permanent installation.
Multicolor spare bulbs cannot replace warm white bulbs and vice versa.

Manual page author

Michael Turner

Technical manual editor

Reviews PDF manuals for structure, safety notes, and practical product details so readers can find the right information quickly.