Electronics / Monitors
User Manual for Agptek SY-818 LED Christmas Projector Light
Quick guide for the Agptek SY-818 LED Christmas Projector Light. Includes installation steps, remote control instructions, troubleshooting, and technical specifications.
Quick answers from the manual
Quick answer
- The Agptek SY-818 is a 2-in-1 LED projector light for indoor/outdoor use. It features ocean wave and pattern projection, remote control operation, and a timer function. p. 3
Key actions
- Set the timer p. 5
- Install the projector p. 3
First start
- Connect the power adapter, place the projector on the ground stake or flat base, and use the remote control to select patterns. p. 3
Show 4 more answers Show less
Problems and fixes
Timing failure
Check for electromagnetic interference, controller function, or reset the timing.
p. 4Maintenance and reset
- To restore factory settings, disconnect the power adapter. p. 4
Technical specifications
| Parameter | Value | Meaning | Pages |
|---|---|---|---|
| Total Power | 7W | Power consumption of the unit. | p. 4 |
| Waterproof Grade | IP65 (Product), IP44 (Power Supply) | Resistance to water and dust. | p. 4 |
Where to find it in the PDF
- General Introduction p. 3
- Remote Control Instructions p. 5
Table of contents
Quick guide from the manual
The Agptek SY-818 is a 2-in-1 LED projector light designed for both indoor and outdoor decoration. It features two projection heads: one for RGBW water wave effects and another for pattern projection. The device is weather-resistant and includes a remote control for easy operation.
Installation
The projector can be installed in two ways:
- Outdoor: Use the included ground stake to secure the unit into the ground.
- Indoor: Use the flat base to place the unit on flat surfaces or secure it to a wall using screws.
Ensure the projector is placed 16.4 to 26.3 feet (5-8 meters) from the projection surface for optimal brightness and clarity.
Remote Control Instructions
The remote control allows you to manage the following functions:
- Pattern Control: Switch between single shapes, multi-shapes, and water patterns. Start/stop patterns.
- Timing Function: Set the timer for 4, 6, or 8 hours. Press the timing button once to enable (lamp flashes twice) and again to disable (lamp flashes three times).
Memory Function
The device remembers the last mode used before turning off. Note: Disconnecting the power adapter directly will reset the device to factory settings. Always turn off the projector using the remote control to preserve settings.
Troubleshooting
- Timing failure: Check for electromagnetic interference or reset the timing function.
- Low brightness: Ensure the projector is used in a dark environment.
- Vague shapes: Adjust the projection distance; the recommended range is 5-8 meters.
Specifications
- Power Input: 100-240V, AC50/60Hz, 1000mA
- Total Power: 7W
- Waterproof Grade: IP65 (Product), IP44 (Power Supply)
- Working Temperature: 5°F to 113°F (-15°C to 45°C)
- Power Cord Length: 16.4ft
Practical help
Common problems
Timing failure
Check for electromagnetic interference, ensure the controller is working, or reset the timing function.
Low brightness and visibility
Use the projector in a dark environment; the darker the surroundings, the brighter the effect.
Shapes are vague
Adjust the projection distance. The recommended distance is 5-8 meters.
Settings reset after restart
Do not disconnect the power adapter directly. Turn off the projector using the remote control to save settings.
Before use
- Check package contents (Projector, Remote, Adapter, Stake, Base, Screws).
- Choose installation method (Ground stake for outdoor, flat base for indoor).
- Ensure the power adapter is protected from direct rain (IP44).
- Place the projector 16.4-26.3ft (5-8m) from the projection surface.
- Use the remote control to power off the device to maintain memory settings.
Show more Show less
Specs in practice
- Waterproof Grade
- IP65 for the projector (dust-tight and water-resistant), IP44 for the power supply (protected against splashing water).
- Working Temperature
- 5°F to 113°F (-15°C to 45°C).
Images and diagrams
- The remote control diagram shows buttons for pattern selection (single/multi-shapes), water pattern control (circulate, start/stop, +/-), and timing functions (4h, 6h, 8h).
Model compatibility
- Suitable for both indoor and outdoor decoration.
Manual page author
Michael Turner
Technical manual editor