Home Appliances / Space Heaters
User Manual for Flama 2334FL Mica Radiator
Quick guide for the Flama 2334FL Mica Radiator. Learn how to assemble the feet, operate the power settings, use the anti-frost function, and maintain your heater safely.
PDF source: Français · summary: English
Quick answers from the manual
Quick answer
- The Flama 2334FL is a mica radiator with two power settings (0.7kW and 1.5kW) and an adjustable thermostat with an anti-frost function. It must be used in an upright position and kept away from flammable materials. p. 4, 9
Key actions
- Assemble the feet p. 4, 9
- Adjust power settings p. 4, 9
First start
- Unroll the cable, plug into a grounded outlet, and set the power selector to I or II. p. 4, 9
Show 4 more answers Show less
Problems and fixes
Overheating
Unplug and wait 30 minutes before restarting.
p. 8Maintenance and reset
- Clean grilles of dust and lint; use a dry, soft cloth. p. 5, 9
Technical specifications
| Parameter | Value | Meaning | Pages |
|---|---|---|---|
| Nominal Heat Output | 1.5 kW | Maximum power | p. 6, 10 |
| Minimum Heat Output | 0.7 kW | Minimum power | p. 6, 10 |
Where to find it in the PDF
- Safety Instructions p. 2, 3, 7, 8
- Operation and Assembly p. 4, 9
- Technical Data p. 6, 10
Table of contents
Quick guide from the manual
The Flama 2334FL is a mica radiator designed for well-insulated spaces or occasional use. Before first use, ensure the feet are correctly assembled. Always operate the unit in an upright position and keep it at least 1 meter away from flammable materials like curtains or fabrics. The device features an automatic safety system that shuts it down in case of overheating; if this occurs, unplug the unit and wait approximately 30 minutes before restarting.
Description
The radiator consists of the following components:
- 1. Grille
- 2. Power selector
- 3. Thermostat regulator knob
- 4. Indicator light
- 5. Feet
- 6. Handle
Assembly
Mounting the feet: Place the feet on the ends of the bottom part of the appliance. Align the holes in the feet with the axes located on the bottom area.
Operation
Usage:
- Unroll the power cable completely.
- Connect the appliance to the power supply. The indicator light will turn on and remain lit until the appliance is disconnected.
- Set the power selector to the desired position:
- Position 0: Off.
- Position I: Minimum power (0.7 kW).
- Position II: Maximum power (1.5 kW).
- Adjust the temperature by turning the thermostat regulator knob.
Anti-frost function: With the thermostat regulator knob in the anti-frost position (*) and the power selector activated, the appliance will automatically turn off if the ambient temperature falls below 5ºC.
Maintenance and Cleaning
Before performing any maintenance or cleaning, ensure the radiator is disconnected from the power supply and has cooled down. Keep the air inlet and outlet grilles clean of dust and lint. Clean the exterior with a soft, dry cloth. Do not use chemical or abrasive products, or metallic scourers, as these may damage the surface.
Safety Warnings
- Do not immerse the appliance in water or any other liquid.
- Do not cover the appliance to avoid overheating.
- Do not place the appliance directly under a power outlet.
- Do not use the appliance near bathrooms, showers, or swimming pools.
- Keep children under 3 years old away unless continuously supervised.
- Children between 3 and 8 years old should only operate the device if it is installed in its normal operating position and they are supervised or instructed on safe use.
- If the power cord is damaged, it must be replaced by an authorized Flama Technical Assistance Service.
Manufacturer information
FLAMA, SA
Practical help
Common problems
Heater does not turn on
Check if the unit is properly connected to the power supply and verify that the circuit breaker is at least 10A.
Unit overheated
The safety system has triggered. Unplug the device and wait approximately 30 minutes before connecting it again.
Before use
- Ensure the supply voltage matches the rating on the appliance label.
- Assemble the feet correctly on the bottom of the unit.
- Place the unit on a flat, stable surface.
- Ensure the unit is at least 1 meter away from flammable materials.
- Check that the power cord and plug are not damaged.
Show more Show less
Specs in practice
- Nominal Heat Output
- 1.5 kW (Maximum power setting)
- Minimum Heat Output
- 0.7 kW (Minimum power setting)
Model compatibility
- Suitable only for well-insulated spaces or occasional use.
Manual page author
Michael Turner
Technical manual editor