Home / Electrical Outlets & Switches
User Manual for GE 20105LO LED 600 7MM Lights
Quick guide for GE 20105LO LED 600 7MM Lights. Includes safety instructions, lamp replacement steps, and troubleshooting tips for your holiday lighting.
Quick answers from the manual
Quick answer
- This manual provides safety, maintenance, and troubleshooting instructions for the GE 20105LO LED 600 7MM Lights. Key maintenance includes replacing lamps with 3.3V, 0.066W LEDs and inspecting wires before use. p. 1
Key actions
- Replace lamp p. 1
- Inspect before use p. 1
First start
- Plug in and ensure foot pedal is in the on position. p. 1
Problems and fixes
Product does not light
Check connections, ensure foot pedal is on, and push LEDs into sockets.
p. 1Technical specifications
| Parameter | Value | Meaning | Pages |
|---|---|---|---|
| Lamp Voltage | 3.3V | Required voltage for replacement lamps | p. 1 |
| Lamp Wattage | 0.066W | Required wattage for replacement lamps | p. 1 |
Where to find it in the PDF
- Safety and Troubleshooting p. 1
Table of contents
Important Information
This product is intended for indoor use only. It is a seasonal product and not designed for permanent installation. Always follow basic electrical safety precautions when using this product.
- Do not mount or place near gas or electric heaters, fireplaces, candles, or other heat sources.
- Do not secure wiring with staples or nails, or place on sharp hooks.
- Unplug the product when leaving the house, retiring for the night, or if left unattended.
- Do not hang ornaments or other objects from the cord, wire, or light string.
- Do not close doors or windows on the product or extension cords.
- Do not cover the product with cloth, paper, or any material not part of the product when in use.
Use and Care
If placing the product on a live tree, ensure the tree is well-maintained, fresh, and stable. Keep the tree holder filled with water. Before using or reusing, inspect the product carefully. Discard any products that have cut, damaged, or frayed wire insulation, cracks in the lampholders, loose connections, or exposed copper wire.
User Servicing Instructions
To replace a lamp, follow these steps:
- Grasp the plug and remove it from the receptacle. Do not unplug by pulling the cord.
- Pull the lamp and plastic base straight out of the lampholder.
- Replace the lamp with only a 3.3 Volt, 0.066 Watt, LED type lamp (provided with the product).
If the new lamp base does not fit in the lampholder:
- Remove the base of the burned-out lamp by straightening the lamp leads and gently pulling the lamp out.
- Thread the leads of the new lamp through the holes in the old base, with one lead in each hole.
- After the lamp is fully inserted into the base, bend each lead up so that the leads touch the contacts inside the lampholder.
Troubleshooting
If the product does not light, ensure the foot pedal is in the 'on' position and that all male/female connectors are fully inserted. If an LED is missing or fails to light, replace it with a spare LED provided with the product. For issues with color changing, contact customer support.
Practical help
Common problems
Product does not light
Check that the foot pedal is on, ensure connectors are fully inserted, and push each LED base firmly into the socket.
LED is missing
Mark the socket with tape, unplug the set, and replace the missing LED with a spare.
LED fails to light
Replace the bad LED as soon as you find it.
Before use
- Inspect for cut, damaged, or frayed wire insulation.
- Check for cracks in lampholders or enclosures.
- Ensure there are no loose connections or exposed copper wire.
- If using on a live tree, ensure the tree is fresh and well-maintained.
Specs in practice
- Lamp Voltage
- 3.3 Volt
- Lamp Wattage
- 0.066 Watt
Model compatibility
- Indoor use only
- Not for permanent installation
Manual page author
Emily Carter
User documentation editor
Prepares concise manual descriptions and highlights the most useful setup, operation, and maintenance information for readers.