Power / USB Chargers
Instruction Manual for Hyper 2.4Ghz LED RC Truck
Quick guide for the Hyper 2.4Ghz LED RC Truck. Learn how to install batteries, charge the car, and operate the remote control safely.
Quick answers from the manual
Quick answer
- The Hyper 2.4Ghz LED RC Truck requires a 3.7V 500mAh Li-ion battery pack for the car and 2x 1.5V AA batteries for the controller. Charging is performed via the included USB cable. p. 1
Key actions
- Install 3.7V battery in the car and 2x AA batteries in the controller. p. 1
- Charge the car battery using the USB charger until the red light indicates completion. p. 1
Problems and fixes
Harmful interference
Reorient/relocate antenna, increase separation, or consult a technician.
p. 1Technical specifications
| Parameter | Value | Meaning | Pages |
|---|---|---|---|
| Car Battery | 3.7V 500mAh Li-ion | Rechargeable battery pack | p. 1 |
| Controller Battery | 2x 1.5V AA | Standard alkaline batteries | p. 1 |
Where to find it in the PDF
- Instruction Manual p. 1
Table of contents
Manual images
Click an image to enlargeQuick guide from the manual
This manual provides essential instructions for the setup and operation of the Hyper 2.4Ghz LED RC Truck. Key procedures include installing batteries in both the vehicle and the controller, as well as the correct method for charging the car's battery pack.
Battery Installation
Car Battery
The car uses a 3.7V 500mAh Li-ion battery pack. Ensure the car is switched to the OFF position before installing or removing the battery. Insert the battery pack into the designated compartment as shown in the diagram.
Controller Battery
The remote controller requires 2 x 1.5V AA batteries (not included). Open the battery cover on the back of the controller and insert the batteries, ensuring they are placed with the correct polarity (+ and -) as indicated inside the compartment.
Charging the Car Battery
To charge the car battery pack:
- Disconnect the battery pack from the car.
- Connect the 3.7V battery pack to the provided USB charger.
- Connect the USB charger to a suitable USB adaptor.
- The red light on the charger indicates that the battery is charging.
Safety Precautions
- Do not operate the vehicle during thunderstorms or rain.
- Avoid driving in sand, water, or snow.
- Do not submerge the car or controller in water.
- Adult supervision is recommended when operating the car.
- Remove all batteries when the car is not in use to prevent accidental operation.
- Do not operate the car on streets or highways.
- Keep fingers, hair, and loose clothing away from the tires, gears, and motor while the car is switched ON.
- Do not leave the car or transmitter near sources of heat or under direct sunlight for long periods.
Contact Information
Distributed by: Hyper Toy Company. Toll-free: 1-866-204-9737. Address: 177 Malaga Park Dr. Malaga, NJ 08328.
Manufacturer information
Hyper Bicycles, Inc.
Practical help
Common problems
Car does not move
Ensure the car is switched ON, batteries are fresh/charged, and the controller is paired.
Interference during operation
Reorient or relocate the receiving antenna, or increase the separation between the equipment and the receiver.
Before use
- Charge the 3.7V Li-ion battery pack fully before first use.
- Install 2 fresh 1.5V AA batteries in the controller.
- Ensure the car power switch is in the OFF position during charging.
- Check that the battery polarity (+/-) is correct in both the car and controller.
Specs in practice
- 3.7V 500mAh Li-ion
- The rechargeable battery pack specifically for the RC car.
Images and diagrams
- The manual includes a diagram for the car's battery compartment showing the battery pack and the ON/OFF switch.
- A diagram for the controller shows the battery compartment and correct AA battery orientation.
- A charging diagram illustrates the connection between the battery pack, USB cable, and power source.
Model compatibility
- The car is designed for residential use.
- The transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Manual page author
Michael Turner
Technical manual editor
Reviews PDF manuals for structure, safety notes, and practical product details so readers can find the right information quickly.