Electronics / Monitors
Installation Guide for Samsung SKK-AT Stacking Kit
Complete installation guide for the Samsung SKK-AT Stacking Kit. Learn how to safely stack your dryer on a Samsung washing machine, including step-by-step assembly, model compatibility, and safety precautions.
Quick answers from the manual
Quick answer
- The SKK-AT Stacking Kit is designed to safely stack a Samsung dryer on top of a Samsung front-load washing machine. Installation requires leveling the dryer, identifying the correct mounting holes based on your machine's capacity and model, and securing the stacking guides with the provided brackets and screws. p. 1
Key actions
- Level the dryer feet p. 1
- Identify mounting holes p. 1
- Secure stacking guides p. 1
Technical specifications
| Parameter | Value | Meaning | Pages |
|---|---|---|---|
| Capacity Threshold | 22 kg / 23 kg | Determines which assembly holes to use on the stacking guides. | p. 1 |
Show 1 more answers Show less
Where to find it in the PDF
- Installation Guide p. 1, 2
Table of contents
Manual images
Click an image to enlargeQuick Guide from the Manual
This guide provides instructions for installing the Samsung SKK-AT Stacking Kit, which allows you to safely stack a Samsung dryer on top of a Samsung front-load washing machine. Important: This kit is compatible with Samsung front-load washing machines (16 kg+) and dryers (14 kg+) released after 2009. Always use at least two people to lift the dryer.
Safety Precautions
- Heavy Object: The dryer is large and heavy. Use at least two people to move it to avoid injury.
- Power: Disconnect the power cord before starting the installation.
- Drainage: Ensure the drain hose is connected directly to a drain system, not a water tank.
- Stability: The dryer must be firmly installed on top of the washing machine. Do not install the washing machine on top of the dryer.
Required Tools
- Crosshead screwdriver
- Pen
- Gloves
- Level
Installation Steps
- Leveling: Tighten all four leveling feet of the dryer completely and ensure it is level. Connect the drain hose to the drain system.
- Preparation: Pull the washing machine out slightly. Remove the screws from the caps on the top panel of the washing machine.
- Hole Selection: Check the washing machine capacity (22 kg or less vs. 23 kg or more) and identify the correct assembly holes on the stacking guides.
- Model Identification: Use the model name to locate the correct assembly holes on the top cover brackets.
- Bracket Installation: Install the top cover brackets onto the stacking guides using M4 x L16 screws.
- Positioning: Place the assembled stacking guides on the curved edges of the washing machine's top cover. Reattach the top cover caps.
- Alignment: Assemble the bracket guide to the stacking guides at the front. Remove the release liner from the double-sided tape and attach the guides to the washing machine.
- Protection: Place a protective mat over the front end of the stacking guides and secure it with foam tape.
- Lifting: Lift the dryer and place it on the stacking guide. Push the dryer until the rear legs lock into the U-shaped slots.
- Finishing: Remove the foam tapes and protective mat.
- Alignment Check: Ensure the front edges of the stacking guides align with the dryer's side frames.
- Securing: Reattach the bracket guide to the stacking guides using M4 x L16 flat-head screws.
- Front Cover: Install the front cover (A) if applicable. Ensure the side marked 'UP' is facing up.
Manufacturer information
Samsung Electronics
Practical help
Common problems
Dryer is not level
Tighten all four leveling feet completely and use a spirit level to ensure balance.
Drain hose connection
Connect the drain hose directly to your drain system. Do not use a water tank.
Incompatible model
Verify compatibility: 16kg+ washing machines and 14kg+ dryers released after 2009.
Before use
- Ensure at least two people are available to lift the dryer
- Disconnect the power cord from the wall outlet
- Level the dryer using a spirit level
- Check washing machine capacity (22kg/23kg threshold)
- Verify model compatibility (AA/AB/B* types)
Show more Show less
Images and diagrams
- Step 16: Levelling feet adjustment
- Step 18/19: Hole selection based on machine capacity and model
- Step 24: Lifting the dryer onto the stacking guide
- Step 27/28: Front cover installation
Model compatibility
- Compatible with Samsung front-load washing machines (16 kg+)
- Compatible with Samsung dryers (14 kg+)
- Only for models released after 2009
Manual page author
David Miller
Documentation analyst