Tools / Power Tools
User Manual for Ferrex 20V Li-Ion Cordless Blower Skin
Quick guide for the Ferrex 20V Li-Ion Cordless Blower Skin. Includes assembly instructions, operation tips, maintenance, troubleshooting, and technical specifications.
Quick answers from the manual
Quick answer
- The Ferrex 20V Li-Ion Cordless Blower is a garden tool for moving leaves and debris. It requires an ALDI 20V Xfinity Plus battery (sold separately) and features variable speed control. p. 5, 15
Key actions
- Attach the blow tube by pressing the release button and sliding it into the motor housing. p. 14
- Install the battery pack by sliding it into the compartment until it clicks. p. 14
First start
- Ensure the battery is charged, insert it into the blower, and move the switch to the desired speed setting (1 to MAX). p. 14, 15
Problems and fixes
Product does not start
Check battery installation, charge level, or temperature.
p. 20Maintenance and reset
- Clean the blower regularly after each use with a damp cloth. Do not use water spray or solvents. p. 17
Technical specifications
| Parameter | Value | Meaning | Pages |
|---|---|---|---|
| Rated voltage | 20 V d.c. | Operating voltage | p. 20 |
| Blower speed | 138 km/h | Maximum air velocity | p. 20 |
Where to find it in the PDF
- Parts List p. 13
- Assembly p. 14
Table of contents
Manual images
Click an image to enlargeQuick guide from the manual
The Ferrex 20V Li-Ion Cordless Blower Skin is designed for residential use to move yard leaves and debris. Before operating, ensure you have read all safety warnings. Always wear appropriate personal protective equipment, including eye protection, a dust mask, and hearing protection. This unit requires an ALDI 20V Xfinity Plus battery and charger, which are not included with the skin.
Product description
The blower consists of the following main components:
- On/off switch with variable speed control
- Handle
- Battery pack compartment
- Motor housing
- Blow tube
- Tube release button
- Battery pack release button
Assembly
Before assembling or disassembling the blower tube, ensure the on/off switch is in the 0 (Off) position and the battery pack is removed.
- Unpacking: Lay all parts on a flat, stable surface.
- Tube assembly: Press the tube release button and slide the blow tube into the motor housing until it aligns with the arrow on the housing.
- Battery installation: Depress the battery pack release button to slide the battery pack into the compartment. Ensure it is securely seated.
Operation
To start the blower, move the on/off switch to settings 1, 2, 3, 4, or MAX. Speed 1 is the lowest, and MAX is the highest. To stop, move the switch to the 0 position. Note that the blower may run for a few seconds after switching off.
User tips:
- Hold the blow tube approximately 20 cm above the ground.
- Use a sweeping motion from side to side.
- Advance slowly, keeping debris in front of you.
- Inspect the area for hard objects like rocks or bolts before starting to prevent damage.
Maintenance and storage
Remove the battery pack before performing any maintenance. Clean the blower regularly after each use. Keep the blower dry and do not spray with water. Use only a damp cloth and mild soap for cleaning. Do not use solvents or detergents. Store the blower indoors in a cool, dry, and clean location, out of the reach of children.
Troubleshooting
If the product does not start, check the following:
- Ensure the battery pack is installed correctly.
- Check if the battery capacity is low and recharge if necessary.
- If the battery pack is too hot or too cold, allow it to reach a suitable temperature.
Technical specifications
- Rated voltage: 20 V d.c.
- No-load speed: 17000 RPM
- Blower speed: 138 km/h
- Air volume: 590 m3/h
- Machine weight: 1.96 kg
Practical help
Common problems
Product does not start
Check if the battery is installed correctly, check battery charge level, or allow the battery to reach a normal operating temperature if it is too hot or cold.
Before use
- Check that all parts are present and undamaged.
- Ensure the battery is charged.
- Wear eye protection, a dust mask, and hearing protection.
- Inspect the area for hard objects like rocks or bolts.
- Ensure the on/off switch is in the 0 position before inserting the battery.
Specs in practice
- Rated voltage
- 20 V d.c. (requires compatible 20V Xfinity Plus battery).
- No-load speed
- 17000 RPM (maximum motor speed without load).
- Blower speed
- 138 km/h (maximum air velocity).
Images and diagrams
- The parts list diagram identifies the switch, handle, battery compartment, motor housing, and tube release button.
- Assembly diagrams show the alignment of the blow tube with the motor housing arrow.
- Operation diagrams illustrate the variable speed switch positions.
Model compatibility
- Compatible only with the ALDI range of 20V Xfinity Plus Batteries and Chargers.
Manual page author
David Miller
Documentation analyst
Organizes user manual content into clear summaries, with attention to model details, product context, and everyday usability.