Industrial / Space Heaters
User Manual for Sealey PEH2001 Industrial PTC Fan Heater
Comprehensive user guide for the Sealey PEH2001 industrial fan heater. Includes safety instructions, operating procedures, technical specifications, and maintenance guidelines.
Quick answers from the manual
Quick answer
- The Sealey PEH2001 is an industrial PTC fan heater with two heat settings (1000W/2000W) and a fan-only mode. It is controlled via a rotary switch and a thermostat knob. p. 2
Key actions
- Select heat setting p. 2
- Switch off p. 2
First start
- Positioning p. 2
Problems and fixes
Unit is hot
Do not touch the outlet grille during or immediately after use; allow to cool.
p. 2Maintenance and reset
- Maintenance safety p. 2
Technical specifications
| Parameter | Value | Meaning | Pages |
|---|---|---|---|
| Power | 1000/2000W | Adjustable heat output | p. 2 |
| Voltage | 230V | Operating voltage | p. 2 |
Where to find it in the PDF
- Safety and Wiring p. 1
- Operation and Specs p. 2
Table of contents
Manual images
Click an image to enlargeQuick guide from the manual
The Sealey PEH2001 is an industrial PTC fan heater designed for indoor use in well-insulated areas. It features two heat settings (1000W and 2000W) and a fan-only mode. Always ensure the heater is placed on a level surface with at least 2 meters of clearance in front of the unit. Never cover the heater or use it in wet environments like bathrooms.
Safety Instructions
Electrical Safety:
- Inspect power supply leads, plugs, and connections for wear or damage before use.
- Sealey recommends using an RCD (Residual Current Device) with all electrical products.
- If the cable or plug is damaged, switch off the electricity supply and have it repaired by a qualified electrician.
- The product is fitted with a BS1363/A 13 Amp 3-pin plug.
- Wiring: Connect the Green/Yellow wire to Earth (E), Brown to Live (L), and Blue to Neutral (N).
General Safety:
- Disconnect from the mains power supply before servicing or maintenance.
- Only use the heater in an upright position on a level surface.
- Do not use the heater near flammable liquids, solids, or gases.
- Do not place the heater below an electrical socket outlet.
- Do not use a timer or remote device to operate the heater.
- Keep the area in front of the outlet grille clear.
- Allow the unit to cool before storage.
Heater Operation
To operate the heater:
- Place the heater on a level floor.
- Plug the heater into the mains supply.
- Use the rotary switch on the top of the heater to select the desired output: Fan only, Half heat, or Full heat.
- Use the second knob to adjust the thermostat.
- To switch the unit off, turn the rotary switch to '0'.
- Allow the unit to cool down before handling or storing.
Maintenance
Before performing any maintenance, ensure the unit is unplugged from the mains power supply, cool, and on level ground. Do not use the heater without the grilles fitted. Sealey recommends that all repairs are carried out by a qualified electrician.
Technical Specifications
- Model No: PEH2001
- Power Settings: 1000W / 2000W
- Supply: 230V
- Dimensions (WxDxH): 210 x 160 x 217 mm
- Weight: 1.75 kg
Manufacturer information
Sealey Group
Practical help
Common problems
Heater does not turn on
Check the power supply, ensure the plug is securely connected, and verify the fuse in the plug.
Unit overheating or cutting out
Ensure the air inlet and outlet grilles are not obstructed and that there is at least 2 meters of clearance in front of the heater.
Before use
- Inspect power supply leads and plugs for wear or damage.
- Ensure the heater is on a level, upright surface.
- Check that the area is free from flammable materials.
- Ensure there is at least 2 meters of clearance in front of the heater.
- Verify the voltage rating matches your power supply.
Specs in practice
- Power Settings
- Allows selection between 1000W (half heat), 2000W (full heat), or fan-only mode.
Images and diagrams
- The wiring diagram illustrates the correct connection for a BS1363/A 13 Amp 3-pin plug: Green/Yellow wire to Earth (E), Brown wire to Live (L), and Blue wire to Neutral (N).
Model compatibility
- For indoor use only.
- Not suitable for bathrooms, shower rooms, or wet/damp environments.
- Only suitable for well-insulated areas or occasional use.
Manual page author
Michael Turner
Technical manual editor
Reviews PDF manuals for structure, safety notes, and practical product details so readers can find the right information quickly.