Tools / Automotive Tools
User Manual for Sealey SX207.V2 22PC Locking Wheel Nut Key Set - BMW
Quick guide for the Sealey SX207.V2 22PC Locking Wheel Nut Key Set for BMW. Includes operation steps, safety instructions, and component list.
Quick answers from the manual
Quick answer
- The Sealey SX207.V2 is a 22-piece locking wheel nut key set for BMW vehicles. It includes an adaptor that works with 1/2" drive or 21mm sockets to remove locking wheel nuts. p. 1
Key actions
- Remove wheel nut p. 1
- Tighten wheel nut p. 1
Problems and fixes
Key stuck in adaptor
Use the drift to aid removal of key from adaptor.
p. 1Show 3 more answers Show less
Maintenance and reset
- Keep keys and adaptor clean and store in case provided. p. 2
Technical specifications
| Parameter | Value | Meaning | Pages |
|---|---|---|---|
| Compatibility | BMW vehicles | Designed for BMW locking wheel nuts | p. 1 |
Where to find it in the PDF
- Safety and Operation p. 1
- Maintenance and Warranty p. 2
Table of contents
Quick Guide
The Sealey SX207.V2 is a specialized tool set designed for the removal of locking wheel nuts on BMW vehicles. The set includes 20 specific keys and an adaptor compatible with 1/2" drive or 21mm sockets. Always ensure the tool is in good condition before use and follow standard workshop safety practices.
Introduction
This set is intended for distribution to bona fide vehicle dealers and repair centres. It provides a comprehensive range of keys to service various BMW locking wheel nut configurations.
Contents
The set includes the following components:
- SX207.V2-01: Locking Wheel Nut Socket 1/2" Dr.-BMW
- SX207.V2-02: Locking Wheel Nut Bar
- SX207.V2-03 to SX207.V2-22: Individual Locking Wheel Nut Keys (numbered 41 through 60)
Operation
- Select the correct locking wheel nut key for the vehicle and push it into the adaptor.
- Place the key over the wheel nut or bolt and rotate until the key slots securely into the wheel bolt/nut.
- Attach either a 1/2" drive or a 21mm socket to the key adaptor.
- Turn the tool anti-clockwise to remove the wheel bolt or nut.
- Use the provided drift to aid in the removal of the key from the adaptor if necessary.
- After use, replace the key, adaptor, and drift in the carry case.
- To replace the bolt or nut, reverse the removal operation. Always use a torque wrench to tighten the bolt/nut to the manufacturer's specification.
Maintenance
To ensure longevity and performance, keep all keys and the adaptor clean. Store the components in the provided carry case when not in use.
Safety
- Do not use the tool if it is damaged or thought to be faulty.
- Do not use worn or damaged sockets.
- Do not use the tool for tasks it was not designed to perform.
- Do not operate the tool if you are tired or under the influence of alcohol, drugs, or medication.
- Ensure you have received proper instruction from a qualified person before using the tool.
- Maintain correct balance and footing; ensure the floor is not slippery and wear non-slip shoes.
- Keep children and non-essential persons away from the working area.
- If jacking up a vehicle, refer to the manufacturer's instructions for the vehicle and the jack.
Manufacturer information
Sealey Group
Practical help
Common problems
Key stuck in adaptor
Use the drift tool included in the set to assist in removing the key from the adaptor.
Before use
- Ensure the tool is not damaged or faulty.
- Verify the correct key for the specific BMW vehicle is selected.
- Ensure you have a 1/2" drive or 21mm socket available for use with the adaptor.
- Ensure the floor is not slippery and you have proper footing.
- Ensure you have been instructed in the use of the tool by a qualified person.
Show more Show less
Images and diagrams
- The set contains 20 distinct keys (numbered 41-60) to fit various BMW locking wheel nuts.
- The adaptor acts as the interface between the key and your drive tool.
Model compatibility
- Designed specifically for BMW vehicles.
Manual page author
David Miller
Documentation analyst