Industrial / Vacuum Cleaners
User Guide for RIDGID RE 12-M Connector Compatibility Chart
Quick guide for the RIDGID RE 12-M connector compatibility chart. Includes inspection, installation, die marking explanations, and compatibility guidelines for various connectors.
Table of contents
Quick Guide from the Manual
This document serves as a compatibility guide for the RIDGID RE 12-M Manual Hydraulic Crimping Tool. It provides instructions for inspecting and installing crimping dies, explains the die marking system, and outlines compatibility with various electrical connectors.
Inspection and Installation
Before using the tool, perform the following steps:
- Clean and Inspect: Wipe the dies clean and inspect them for wear, corrosion, modifications, damage, or other issues that could affect safe operation.
- Verify Compatibility: Ensure dies are clearly marked, matched to each other, and appropriate for the specific application. Do not use damaged, mismatched, or inappropriate dies.
- Installation: Install the dies according to the head instructions. Dies should fit snugly and securely, and the crimping profiles must align.
- Caution: Do not force dies into the head. If there are any issues with die fit, do not use the dies.
- Manufacturer Instructions: Always follow the electrical connector manufacturer's instructions, including information on crimp location and order.
Understanding Die Markings
RIDGID dies are marked using a specific code format: XX Y - TTT - ZZ SSSS VVV.
- XX (Outside Die Profile): RD = Round Die, SD = Square Die.
- Y (Connector Type): H = Hex, D = DIN, K = Klauke Standard, G = Gulifa/Pheonix.
- TTT (Nominal Tool Force): 60 = 60kN (6 Ton), 130 = 130kN (12 Ton).
- ZZ (Connector Material): CU = Copper, AL = Aluminum.
- SSSS (Connector Wire Size): 0-400 mm2, AWG 8 - 4/0 AWG, 250-1000 MCM or kcmil.
- VVV (Unit of Measure): MM = mm2, AWG, MCM = MCM or kcmil.
Compatibility Statements
The dies and equipment listed in this chart have been tested by the Ridge Tool Company to ensure they meet specific standards:
- UL486: Tested for use with the listed electrical connectors and wire.
- UL1976: Classified for use with the listed electrical connectors and wire.
- Ridge Tool Procedures: Tested to confirm that dies fully close and produce crimps in accordance with the manufacturer's intent.
For the most up-to-date compatibility information, visit www.RIDGID.com/CrimpDies.
Official resources from the manual
Manufacturer information
RIDGID
Practical help
Common problems
Dies do not fit or crimping profiles do not align.
Do not force dies into the head. Inspect for damage or mismatch. If fit issues persist, do not use the dies.
Dies show signs of wear, corrosion, or damage.
Do not use damaged, mismatched, or inappropriate dies. Replace with correct, undamaged dies.
Before use
- Wipe dies clean.
- Inspect for wear, corrosion, or damage.
- Confirm dies are clearly marked and matched.
- Verify dies are appropriate for the application.
- Ensure crimping profiles align.
Specs in practice
- XX (Outside Die Profile)
- RD = Round Die, SD = Square Die.
- Y (Connector Type)
- H = Hex, D = DIN, K = Klauke Standard, G = Gulifa/Pheonix.
- TTT (Nominal Tool Force)
- 60kN (6 Ton) or 130kN (12 Ton).
- ZZ (Connector Material)
- CU = Copper, AL = Aluminum.
Model compatibility
- Compatible only with conductor materials and sizes specified in the lug manufacturer's product literature.
- Dies and equipment are classified to UL 1976 for use with the electrical connectors and wire listed in the chart.
Manual page author
Emily Carter
User documentation editor
Prepares concise manual descriptions and highlights the most useful setup, operation, and maintenance information for readers.