Lighting / Work Lights
User Manual for Scangrip MAG Rechargeable Work Light
Quick guide for the Scangrip MAG rechargeable work light. Includes charging instructions, battery maintenance tips, technical specifications, and safety warnings.
Quick answers from the manual
Quick answer
- The Scangrip MAG is a rechargeable LED work light. Charge it using the included USB cable (5V DC 1A). A red light indicates charging, and a green light indicates the battery is fully charged. p. 1, 2
Key actions
- Charge the lamp before first use and frequently thereafter. p. 2
- Remove the battery before disposing of the device. p. 2
First start
- Charge the battery fully before using the lamp for the first time. p. 2
Maintenance and reset
- Recharge frequently and do not leave the battery discharged for long periods. p. 2
Technical specifications
| Parameter | Value | Meaning | Pages |
|---|---|---|---|
| Battery | 3.7V / 2200 mAh Li-ion | Rechargeable lithium-ion battery capacity. | p. 1 |
| Charging Input | 5V DC 1A | Required power input for charging. | p. 1 |
Where to find it in the PDF
- Technical Specifications p. 1
- Safety and Charging Instructions p. 2, 3, 4, 5
Table of contents
Quick Guide
The Scangrip MAG is a rechargeable LED work light. Before using the lamp for the first time, ensure the battery is fully charged. The lamp should be charged frequently and only in indoor environments at a minimum temperature of 0°C.
Technical Specifications
- Light Source: 10 x SMD LED / Spot: High power LED
- Luminous Flux: 150/300 lumen (step 1/2) / Spot: 80 lumen
- Illuminance: 250/500 [email protected] (step 1/2) / Spot: 850 [email protected]
- Battery: 3.7V / 2200 mAh Li-ion
- Charging Input: 5V DC 1A
- Ingress Protection: IP20
- Dimensions: 260 x 61 x 43 mm
- Weight: 252g
Charging Instructions
Use the included USB cable to charge the device. The charging status is indicated by the light on the charger:
- Red light: The battery is currently charging.
- Green light: The charging process is completed.
Battery Maintenance
Proper battery care is essential for the longevity of your work light:
- Recharge the lamp frequently.
- Do not leave the battery in a discharged state for an extended period, as deep discharge can damage the battery.
- Always replace the battery with an original Scangrip battery.
Safety Warnings
- Do not look directly into the beam of light, as this will result in dazzling.
- Do not use the lamp near a naked flame.
- The light source of this lamp is not replaceable; when the light source reaches its end of life, the whole lamp must be replaced.
Disposal
Discarded electrical products must not be disposed of together with household waste. Please use recycling facilities. The battery must be removed from the device before it is disposed of, and the device must be disconnected from the mains during this process.
Manufacturer information
SCANGRIP A/S
Practical help
Common problems
Lamp does not charge
Ensure the charger is connected to a 5V DC 1A power source and the ambient temperature is at least 0°C.
Battery performance is degrading
Avoid leaving the battery in a discharged state for long periods. Recharge the lamp frequently.
Before use
- Charge the battery fully before the first use.
- Ensure the charging environment is at least 0°C.
- Verify the light source is intact.
Specs in practice
- 150/300 lumen
- Two brightness levels (step 1/2) for the main light.
Images and diagrams
- The product features a main light (10 x SMD LED) and a spot light (High power LED).
- Charging status is indicated by red (charging) and green (full) lights.
Model compatibility
- Use only original Scangrip batteries for replacement.
- The light source is non-replaceable; the entire unit must be replaced at the end of its life.
Manual page author
Emily Carter
User documentation editor
Prepares concise manual descriptions and highlights the most useful setup, operation, and maintenance information for readers.