Power / Batteries & Chargers
User Manual for Sealey CP20VMC Battery Charger
Quick guide for the Sealey CP20VMC battery charger. Learn how to safely charge your CP20V series batteries, understand LED indicators, and follow essential safety precautions.
Quick answers from the manual
Quick answer
- The CP20VMC is a mains charger for Sealey CP20V series batteries. A red LED indicates charging, and a green LED indicates the battery is fully charged. p. 2
Key actions
- Insert battery into charger, plug into mains, wait for green LED. p. 2
First start
- Charge the battery prior to its first use as it is shipped in a low charge state. p. 2
Problems and fixes
Charger overheating
Allow the unit to cool for 15 minutes before charging the next battery.
p. 1Technical specifications
| Parameter | Value | Meaning | Pages |
|---|---|---|---|
| Output | 20V DC | Charging voltage | p. 2 |
| Supply | 230V AC~50Hz | Input power requirement | p. 2 |
Where to find it in the PDF
- Safety Instructions p. 1
- Operation and Specifications p. 2
Table of contents
Quick Guide
The Sealey CP20VMC is a mains-powered charger designed specifically for the CP20V series power tool batteries. Before using the charger, ensure the battery is fully charged, as it is shipped in a low-charge state. Always allow the unit to cool for 15 minutes between charging consecutive batteries to prevent overheating.
Safety Instructions
Electrical Safety:
- Inspect power supply leads, plugs, and connections for wear or damage before use.
- Sealey recommends using an RCD (Residual Current Device) with all electrical products.
- This product is fitted with a BS1363/A 13 Amp 3-pin plug. If the plug or cable is damaged, have it replaced by a qualified electrician.
- Do not pull the appliance by the power cable or remove the plug by pulling the cable.
- Class II products are wired with live (brown) and neutral (blue) wires only. Do not connect either wire to the earth terminal.
Battery Charger Safety:
- Use only for CP20V series batteries. Charging other types may cause explosions.
- Do not expose the charger to damp or wet conditions (indoor use only).
- Do not attempt to open, disassemble, or modify the charger or battery pack.
- Do not insert foreign objects into the battery slot.
- Disconnect from the mains power supply when not in use.
Operation
Charging Procedure:
- Ensure the battery is removed from the equipment by depressing the spring-loaded button and sliding the pack out. Do not touch the metal terminals.
- Insert the battery fully and firmly into the charging base. It is designed to fit only one way.
- Plug the charger into the mains and switch on the power.
- The red LED on the charger will illuminate to indicate the battery is charging.
- When the green LED illuminates permanently, the battery is fully charged.
- Remove the battery from the charger and switch off/unplug the charger from the mains.
Technical Specifications
- Model No: CP20VMC
- Applications: CP20VBP2, CP20VBP, CP20VBP4, CP20VBP6
- Output: 20V DC
- Supply: 230V AC ~ 50Hz
Environment and Disposal
Dispose of this product in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE). Recycle unwanted materials instead of disposing of them as waste. Contact your local solid waste authority for recycling information.
Manufacturer information
Sealey Group
Practical help
Common problems
Charger overheating
Allow the unit to cool for 15 minutes before charging the next battery.
Battery not charging
Ensure the battery is seated firmly in the charger and the charger is connected to a live mains supply.
Before use
- Inspect the plug, cable, and charging base for wear or damage.
- Ensure the voltage rating on the appliance suits the power supply.
- Uncoil the power cable between the plug and the charging base.
- Verify the battery is a CP20V series model.
Specs in practice
- Output: 20V DC
- The voltage provided to the battery during the charging process.
- Supply: 230V AC ~ 50Hz
- The standard mains power requirement for the charger.
Images and diagrams
- The fuse rating diagram on page 1 specifies the use of a 3A fuse for the plug.
Model compatibility
- Compatible only with CP20V series batteries (CP20VBP2, CP20VBP, CP20VBP4, CP20VBP6).
Manual page author
Michael Turner
Technical manual editor
Reviews PDF manuals for structure, safety notes, and practical product details so readers can find the right information quickly.