Power / Batteries Chargers
Timex 04K-096000 LCD Analog Digital Watch User Manual
Quick guide for the Timex 04K-096000 watch, covering time and date settings, dual time, alarm, timer, stopwatch, bracelet adjustment, and water resistance precautions.
Table of contents
Quick guide from the manual
This document provides instructions for the Timex 04K-096000 watch, which features both analog hands and a digital LCD display. It covers basic operations, time setting, dual time, alarm, timer, stopwatch, and maintenance.
Time and Date Setting
- Press MODE repeatedly until the time is shown with seconds flashing.
- Press LAP/RESET to set seconds to zero.
- Press START/STOP to select minutes, then LAP/RESET to advance. Hold to increment quickly.
- Repeat for hours (AM/PM), date, month, and day.
- Press MODE to exit.
- To switch between AM/PM and 24-hour format, press and hold START/STOP for 4 seconds.
Dual Time
- Press MODE until the indicator is next to DUAL T.
- Press START/STOP. The hour hand will flash.
- Press LAP/RESET to advance the hour hand.
- Press START/STOP, then LAP/RESET to advance the minute hand.
- Press START/STOP to exit.
Alarm and Chime
- Press MODE until the indicator is next to ALARM.
- Press START/STOP and LAP/RESET simultaneously to enable/disable the alarm or hourly chime.
- To set the alarm time, press MODE to ALARM, then START/STOP. Use LAP/RESET to adjust the hour and minute hands.
Timer
- Press MODE until the indicator is next to TIMER.
- Press LAP/RESET repeatedly to set the countdown minutes (up to 60).
- Press START/STOP to begin the countdown.
- Press START/STOP to pause, or LAP/RESET to reset.
Stopwatch
- Press MODE until the indicator is next to STOP.
- Press START/STOP to start/stop the stopwatch.
- Press LAP/RESET while running to record a split time.
- Press LAP/RESET to reset the stopwatch to zero.
Bracelet Adjustment
For the sliding clasp bracelet:
- Open the locking plate.
- Move the clasp to the desired length.
- Exert pressure while holding the locking plate and slide the clasp back and forth until it engages in the grooves on the underside of the bracelet.
- Press the locking plate down until it snaps closed.
Water and Shock Resistance
The watch is water-resistant to 30 meters. Warning: Do not press any buttons under water. Rinse with fresh water after exposure to salt water.
Battery
The battery is not intended to be replaced by the consumer. Only a jeweler or professional should replace it.
Manufacturer information
Timex Group USA, Inc.
Practical help
Common problems
Alarm or chime not sounding
Ensure the alarm or chime is enabled in the ALARM mode by pressing START/STOP and LAP/RESET simultaneously.
Timer not showing previous setting
If no setting is shown, press LAP/RESET to restore the previously set countdown.
Clasp not holding
Ensure the locking plate is fully snapped closed and the clasp is properly engaged in the bracelet grooves.
Before use
- Check that the watch lens, buttons, and case are intact to maintain water resistance.
- Ensure the battery compartment is secure.
- Verify the current time and date settings.
- Familiarize yourself with the button functions (LIGHT, MODE, START/STOP, LAP/RESET).
Specs in practice
- Water Resistance
- 30 meters (3 ATM). Suitable for daily use, but not for diving.
- Battery Type
- Lithium metal, CR2025 (professional replacement only).
- Stopwatch Capacity
- Up to 24 hours with split time functionality.
Model compatibility
- Not a diver watch; do not use for diving.
- Alarm setting is tied to the primary time zone.
Manual page author
Michael Turner
Technical manual editor
Reviews PDF manuals for structure, safety notes, and practical product details so readers can find the right information quickly.